Berger

Menu
Menu
[vc_row full_width=”stretch_row_content_no_spaces” content_placement=”top” css=”.vc_custom_1481317372265{margin-top: -145px !important;}”][vc_column][vc_single_image image=”10476″ img_size=”full”][/vc_column][/vc_row][vc_row][vc_column width=”5/12″][vc_single_image image=”10089″ img_size=”full”][vc_column_text]

2k Acrylic Primer (Base & Hardener)

[/vc_column_text][vc_column_text][dt_sc_fancy_ul style=”rounded-tick”]
  • Two component product based on Polyvinyl Butyrate Resin and other rust inhibitive ingredients with a suitable Organic Acid Catalyst
  • The product is especially suitable for non ferrous surfaces that are clear composition on modified Epoxy Resins to form a two component product cured with an appropriate catalyst
  • It accepts both two pack and single pack top coats with good adhesion
  • Can be used as a specification primer as per BS5493 and meets the performance of AP2A.
[/dt_sc_fancy_ul][/vc_column_text][/vc_column][vc_column width=”7/12″][vc_tta_tabs][vc_tta_section title=”Designed use” tab_id=”1484301115557-6fa822bd-504d”][vc_column_text]Designed Use:

  1. It can be used as an appropriate primer for non ferrous substrates
  2. Galvanized steel (both new and old)
  3. Copper and Aluminum surfaces
  4. Good acceptance of various topcoats

Availability:

  1. Available as per requirement

Coverage:

  1. The theoretical coverage of VITON 2K ACRYLIC PRIMER would be approximately 7-8 M²/liter per coat at a Dry film thickness of 30 – 40 micron per coat
[/vc_column_text][/vc_tta_section][vc_tta_section title=”Surface preparation” tab_id=”1484301115558-bdaaa16a-9dba”][vc_column_text]Surface preparation:

  1. humid conditions >95% and also dew point of <3% for application
  2. The expected life span is directly related to the surface cleanliness
    1. It is therefore mandatory to remove the grease, oil, wax by solvent cleaning
  3. It is a 2 component product and has to be mixed thoroughly individually before it is mixed together for uniformity
  4. Number of coats: Normally one coat not more than 8 microns in any case
[/vc_column_text][/vc_tta_section][vc_tta_section title=”Method of application” tab_id=”1484301158111-4be422f4-cf30″][vc_column_text]Method of application:

  1. Conventional Spray: It is the most recommended method of application Use standard equipment and a pressure of 2.8-3.0 kg/ cm2 (40-45 psi)
  2. Brush or Roller: This method may be adopted for substrates with difficult shapes or touchup; however care must be taken not to exceed the recommended film thickness and ensure that an even film is applied
  3. Air less spray: For larger areas it is the best recommended method of application but great care must be taken to ensure the recommended film thickness are not exceeded. Use a tip with a wide fan width. Tip Size : 0.22 – 0.30 mm (0.009 – 0.011 in) Pressure: 90 – 130 Kg/cm2 (1300-1800 psi)

Caution:*Not suitable for perpetual wet conditions. The product is extremely sensitive to moisture; dry heat resistance is 70°c. 

Thinning recommendation:

  1. VITON 2K ACRYLIC (SLOW) THINNER and to the extent of maximum of 10% of the paint by volume.
  2. Stir well with a convenient mixing equipment for uniformity to ensure good mixing of all the components.

 

Pack Sizes:

  1. Available in plastic pails of metal tins in 1 and 4 liter packs
[/vc_column_text][/vc_tta_section][/vc_tta_tabs][/vc_column][/vc_row]
× Lets Chat